9 Part 6 USB driver installation guide 1、 Execute installation and click “Install”.
10 2、 Installation is done when this screen displays.
11 3、 Use USB cord to connect WBT-200 to the USB port of computer. Computer will automatically check it and seek driver software by itself. If PC ask
12 4、 The screen will display as below. Click “continue anyway”.
13 5、 Installation completed.
14 6、 Immediately afterwards, PC will ask again to install “GPS Receiver Virtual Com Port” driver. Click “ next ”.
15 7、 Installation completed. To check the installation status, go to the “device manager” .
16 8、 As in the illustration, the USB device (marked in red circle) is correctly installed to PC. The illustration also shows USB being transferred t
17 Part 7 Using with PDA Use of this with PDA for location check. It is necessary to install GTOOL(PPC) first in your PDA. Follow the following steps
18 2、Tap the Bluetooth icon again and select the ”Bluetooth Manager”. 3、From Bluetooth Manager toolbar, tap ”New” to search for any other B
1 Table of contents Contents Part 1 Product introduction 2 Part 2 Features 3 Part 3 Safety notes
19 4、Tap “Explore a Bluetooth device” to view Bluetooth devices services and create a shortcut to them. Click“Next” to continue. 5、Tap
20 6、Select “SPP slave” services and tap “Next” to create a shortcut to it. 7、Tap “Finish” to complete procedure.
21 8、From the “My Shortcuts” tab, tap the “BT-GPS: SPP slave” icon and select the “Connect” option to connect to it. 9、When a connection is
22 Step 2:Using GTOOL(PPC) for locating . The GTOOL(PPC) enables you to view your position by latitude and longitude, speed, heading, and altitude. Ma
23 2、At “My Device” tab, tap the “Program Files”, then select “GTool” case. 3、In the “GTool” case, tap the GTool icon to start it.
24 4、At “Connect Setting” tab, select Bluetooth com port on your PDA at “Select GPS Port” item and click Connect ,than select BT-GPS icon.
25 6、Feature in other tabs : “Log Mode Setting ”:Log mode setting. “Read Log”:Read or clean the Log data. LOG File (*.tks) default path save as “..
26 “NMEA Setting”: Set the NMEA output. “Init. Mode”: Reboot, Factory Reset, Cold Start, and the firmware version. ( Note:If use these features, Bl
27 “Satellite”:View Satellite Information. “Sky Plot”:View Satellite Distribution in the sky.
28 Part 8 Trouble shooting The GPS signal will become weak under the following conditions. If the vehicle enters the tunnel. The GPS signal trans
2 Part 1 Product introduction Overview GPS LED: (Green LED) Green LED Solid light shows location fixing incomplete .Blink light shows locat
29 Bluetooth connection takes 5 seconds for self-check. Each time the device is switched on; it needs 5 seconds before connection. It is normal
3 Part 2 Features WBT-200 is the GSP receiver with internal antenna. u-Nav + iTrax 03 used in its core is high-tech component and included function o
4 Part 3 Safety notes GPS (Global Positioning System) is provided by the United States government. Its accuracy may varies depending on special co
5 Part 4 Quick user guide Package :WBT-200(bluetooth GPS with logger)+USB cable+ sticker +car cigarette lighter power adapter , installation Disk,
6 can best receive GPS signal for acquisitioning. Activate the software of paired device. WTB 200 starts to provide GPS data. Battery charging:
7 Part 5 Operation notes WBT-200 will do self-check once it is powered. Bluetooth and GPS start to work when both Bluetooth LED (glows blue) and GP
8 After positioning, if auto-log function is activated, WBT-200 begins to auto-log the following way. Maximum data up to 25360 Points (or more tha
Commentaires sur ces manuels